| 1 | Levelling soil surface zone. It can be used well in seedbed preparation. |
| 2 | Tillage zone. Tillage depth 4–15 cm. The tines arranged in four rows with optimized geometry and small final spacing ensure excellent full-surface tillage and intensive soil mixing with crop residues. |
| 3 | Furrow-levelling zone. Levelling discs also increase the effect of incorporating crop residues. |
| 4 | Clods crumbling and soil re-compaction zone. Optimal soil re-compaction ensures good water infiltration and soil water capillarity to the surface. |
The semi-mounted 4-row tine cultivator Fantom CLASSIC with low pulling requirement and variable tillage depth up to 15 cm.
Intensive and fine tillage is enabled due to the 170 mm tine spacing. There is a spring protection on the tines with a very high release force of 310 kg on the tip of the tine. The cultivator is characterized by consistent working depth even in more difficult conditions.
The semi-mounted 4-row tine cultivator Fantom CLASSIC with low pulling requirement and variable tillage depth up to 15 cm.
Intensive and fine tillage is enabled due to the 170 mm tine spacing. There is a spring protection on the tines with a very high release force of 310 kg on the tip of the tine. The cultivator is characterized by consistent working depth even in more difficult conditions.
Due to minimum adjusting and lubricating points the operation and subsequent maintenance are very easy steps that anybody can perform.
The advantage of this machine is its multipurposeness and adjustability bringing high work variability.
| Technical parameters | Units | Fantom 650 CLASSIC |
Fantom 850 CLASSIC |
Fantom 1250 CLASSIC |
|---|---|---|---|---|
| Working width | mm | 6 300 | 8 550 | 12 250 |
| Transport width | mm | 3 000 | 3 000 | 3 000 |
| Transport height | mm | 3 650 | 4 000 | 4 000 |
| Total machine length | mm | 8 000 | 8 700 | 8 200 |
| Working depth | mm | 40–150 | 40–150 | 40–150 |
| Number of tines | pcs | 33 | 45 | 64 |
| Tine spacing | mm | 190 | 190 | 190 |
| Number of tine rows | pcs | 4 | 4 | 4 |
| Row spacing | mm | 595–620 | 595–620 | 595–620 |
| Release force of tines | kg | 310 | 310 | 310 |
| Frame clearance | mm | 570 | 570 | 570 |
| Working performance | ha/h | 4,4–7,2 | 6,8–10,2 | 10,0–15,0 |
| Towing vehicle 1 | kW HP |
200–300 270–410 |
245–370 330–500 |
330–440 450–675 |
| Working speed | km/h | 8–12 | 8–12 | 8–12 |
| Maximum transport speed 3 | km/h | 30 | 30 | 30 |
| Maximum slope availability | ° | 6 | 6 | 6 |
| Number of hydraulic circuits / pressure | bar | 5 / 200 | 5 / 200 | 5 / 200 |
| Number of hydro-couples / type | 8 / ISO 12,5 | 8 / ISO 12,5 | 8 / ISO 12,5 | |
| Tractor hitch requirement | TPH cat. 3; peg Ø 50, 70 mm; hinge K80 | TPH cat. 3; peg Ø 50, 70 mm; hinge K80 | peg Ø 50, 70 mm; hinge K80 | |
| Machine weight 2 | kg | 7 000 | 8 900 | 12 400 |
1 Recommended towing vehicle, the actual pulling force may significantly change according to the tilling depth, soil conditions, inclination of land, wear of working units and their adjustment.
2 Depends on the used type of the roller.
3 Transport / brake system: Follow national provisions valid for transport of machines on public roads. Verify legal provisions valid in the country, regulations on maximum allowable total weights and axle loads and also on necessary possible use of the brake system. If you have any questions, please contact our sales representative.
| Diameter | 580 mm |
| Weight | 220 kg/m |
| Diameter | 586 mm |
| Weight | 200 kg/m |
LTX roller cannot be used for Fantom 850 CLASSIC.
| Diameter | 600 mm |
| Weight | 100 kg/m |
| Diameter | 550/550 mm |
| Weight | 180 kg/m |
Double V-ring cannot be used for Fantom 1250 CLASSIC.
| Diameter | 540/540 mm |
| Weight | 195 kg/m |
Double ring roller cannot be used for Fantom 1250 CLASSIC.
| Diameter | 600 mm |
| Weight | 175 kg/m |
| Diameter | 520/520 mm |
| Weight | 165 kg/m |
Proper selection of the type of the rear roller contributing significantly to the final quality of the tillage is very important. The soil is recompacted by the roller and then it is the same way crumbled and levelled. The selection of the type of the roller depends on the soil type and on the manner of use of the machine.
| Roller | Tube-shaped TRS |
Double ring DRR |
Double DFR |
LTX |
|---|---|---|---|---|
| Crumbling | ●●○○ | ●●●○ | ●●●○ | ●●○○ |
| Stamping | ●●●○ | ●●●● | ●●●● | ●●●● |
| Depth guiding | ●●●○ | ●●●● | ●●●● | ●●●● |
| Resistance against clogging | ●○○○ | ●●●● | ●●●● | ●●●○ |
| Suitability for stony soils | ●●●○ | ●●●○ | ●●●○ | ●●●○ |
| Suitability for wet soils | ●○○○ | ●●●● | ●●●● | ●●●● |
| Heavy soils | ●●○○ | ●●●● | ●●●● | ●●●● |
| Medium soils | ●●●○ | ●●●● | ●●●● | ●●●● |
| Light soils | ●●●● | ●●●● | ●●●● | ●●●○ |
| Roller | Disk SDR |
VR | Double V-ring DVR |
|---|---|---|---|
| Crumbling | ●●●○ | ●●●○ | ●●●○ |
| Stamping | ●●●● | ●●●● | ●●●● |
| Depth guiding | ●●●● | ●●●● | ●●●● |
| Resistance against clogging | ●●●○ | ●●●● | ●●●● |
| Suitability for stony soils | ●●●○ | ●●●○ | ●●●○ |
| Suitability for wet soils | ●●●● | ●●●● | ●●●● |
| Heavy soils | ●●●● | ●●●● | ●●●● |
| Medium soils | ●●●● | ●●●● | ●●●● |
| Light soils | ●●●○ | ●●●● | ●●●● |
| Chisel width | 50 mm |
| Chisel thickness | up to 55 HRC |
| Chisel body hardness | up to 92 HRA |
| Hardness of hard facing | up to 60 HRC |
| Chisel service life | + 400-600 % |
| Chisel width | 50 mm |
| Chisel body hardness | up to 55 HRC |
| Widia plate hardness | up to 92 HRA |
| Share width | 280 mm |
| Share body width | 43 mm |
| Share thickness | 6 mm |
| Body hardness | up to 55 HRC |
| Carbide plate hardness | up to 92 HRA |
For all-area undercutting
| Chisel width | 50 mm |
| Chisel body hardness | up to 55 HRC |
| Widia plate hardness | up to 92 HRA |
| Chisel service life | + 400-600 % |
| Share width | 230 mm |
| Share thickness | 8 mm |
| Body hardness | up to 55 HRC |
 |
Divides 1 tractor circuit into 3 circuits with electronic control.
