Do you like this machine? Write to us.
I am interested in the machine

1

Ground levelling zone. It can be used well in seedbed preparation.

2

Loosening zone. Loosening depth 4 - 15 cm. Optimized geometry chisels in four rows with small final spacing ensure very fine full-area loosening and intensive soil mixing with plant residues.

3

Wave-levelling zone. Levelling discs also increase the effect of incorporating plant residues.

4

Clod crumbling and soil reconsolidation zone. Optimum soil reconsolidation ensures good water infiltration and soil moisture rise.

Half-carried 4-row share cultivator Fantom CLASSIC with low traction resistance and variable processing depth up to 15 cm.

Intensive and fine soil processing

Intensive and fine soil processing is enabled due to the tine spacing of 170 mm. There is a spring protection on the tines with a very high release force of 310 kg on the tip of the ploughshare. The working width of the cultivator is stable even in more difficult conditions.

Half-carried 4-row share cultivator Fantom CLASSIC with low traction resistance and variable processing depth up to 15 cm.

Intensive and fine soil processing

Intensive and fine soil processing is enabled due to the tine spacing of 170 mm. There is a spring protection on the tines with a very high release force of 310 kg on the tip of the ploughshare. The working width of the cultivator is stable even in more difficult conditions.

High performance

  • High working speed up to 12 km/h.
  • Low traction resistance and excellent mixing of the soil due to the optimized design of ploughshares.

 Cultivator Fantom

1 2 3
4

 

  1. Hydraulically controlled front flexi-board leveller for smoothing of the soil surface and crumbling of clods before the whole processing.
  2. Optional working bodies in 4 rows.
  3. The rear coordination disks located behind the working bodies in front of the row of rollers with the aim to level the soil surface in front of the rollers are easily height-adjustable.
  4. Optional rear rollers for various conditions.

High quality of work

  • Precise deep guiding with optimum soil compaction.
  • Excellent penetration of the tines into the soil.
  • Maintenance-free working members fitted with plates of cemented carbides for minimal wear.
  • The design of the ploughshares ensures high passability for plant residues.

Easy operation

Due to minimum of adjusting and lubricating points the operation and subsequent maintenance are very easy steps that anybody can perform.

  • Minimum of lubrication points.
  • Minimum of adjustment points.

Technical parameters

Technical parameters Units Fantom
1250 CLASSIC
Working width mm 12 500
Transport width mm 3 000
Transport height mm  
Total machine length mm 8 220 
Working depth mm 0 - 150
Number of ploughshares pcs 64
Ploughshare spacing mm 190
Number of ploughshare rows pcs 4
Row spacing mm 595 - 620 
Release force of ploughshares kg 310
Frame clearance mm  570 
Working performance ha/h 10,0 - 15,0
Towing vehicle 1 kW
HP
330 - 440
450 - 675
Working speed km/h 8 – 12
Maximum transport speed 3 km/h 20
Maximum slope availability ° 6
Number of hydraulic circuits / pressure bar 4 / 200 
Number of hydrocouples / type   8 / ISO 12,5 
Tractor hitch requirement   peg Ø 50, 70 mm; hinge K80
Machine weight 2 kg 11 220


1 Recommended towing vehicle, the actual pulling force may significantly change according to the processing depth, soil conditions, inclination of land, wear of working members and their adjustment.
2 Depends on the type of the roller used.
3 Transport / brake system: Follow national provisions valid for transport of machines on public roads. Verify legal provisions valid in the country, regulations on maximum allowable total weights and axle loads and also on necessary possible use of the brake system. If you have any questions, please contact our sales representative.

PS - half-carried foldable machine

Accessories

Rollers

Disk roller
Diameter 580 mm
Weight 220 kg/m
LTX roller
Diameter 586 mm
Weight 200 kg/m
Tube roller
Diameter 510 mm
Weight 90 kg/m

Proper selection of the type of the rear roller contributing significantly to the final quality of the processing is very important. The soil is recompacted by the roller and then it is the same way crumbled and levelled. The selection of the type of the roller depends on the soil type and on the manner of use of the machine.

Roller Tube-shaped
TR
LTX  Disk
SDR
Crumbling ●●○○ ●●○○ ●●●○
Stamping ●●●○ ●●●● ●●●●
Depth guiding ●●●○ ●●●● ●●●●
Resistance against clogging ●○○○ ●●●○ ●●●○
Suitability for stony soils ●●●○ ●●●○ ●●●○
Suitability for wet soils ●○○○ ●●●● ●●●●
Heavy soils ●●○○ ●●●● ●●●●
Medium soils ●●●○ ●●●● ●●●●
Light soils ●●●● ●●●○ ●●●○

Chisel

Chisel 50 MULTICARBIDE
Share width 50 mm
Share body hardness up to 55 HRC
Widia plate hardness up to 92 HRA
Hardness of hard facing up to 60 HRC
Share service life + 400-600 %
Chisel 50 MULTICARBIDE PRO
Share width 50 mm
Share body hardness up to 50 HRC
Widia plate hardness up to 92 HRA

 

40 CARBIDE chisel with exchangeable wings
Share width 280 mm
Share body width 43 mm
Share thickness 6 mm 
Body hardness 50 HRC
Carbide plate hardness up to 92 HRA

For all-area undercutting