| 1 | Tractor track cultivation zone. Perfect cultivation of the tracks eliminates uneven emergence of plants after sowing. |
| 2 | Basic soil levelling zone. Precisely levelled soil surface allows uniform subsequent compaction and cultivation the seedbed. |
| 3 | Soil pre-compaction zone by the front roller. The front roller crumbles clods on the surface, but at the same time it compacts the soil and restores the soil capillarity. |
| 4 | Seedbed zone. The soil is cultivated by the share section to the set depth. The depth should be the same as the future sowing depth. Duck foot shares allow full-surface undercut and weed control. |
| 5 | Furrow-levelling zone behind a share cultivating section. |
| 6 | Rear roller soil compaction zone. The roller finely crumbles clods and ensures the final compaction of the seedbed so that the soil capillarity is fully restored. Intensive soil water capillarity to the surface ensures good emergence of plants even in the dry season. |
| 7 | Final soil levelling zone. The rear bar or final rollers ensure a perfect levelled surface with minimum clods for subsequent sowing. |
Seedbed combinators Kompaktomat are time-tested machines designed for seedbed preparation of the soil after ploughing.
Semi-mounted machines are offered with the working span from 3 m to 9.7 m. Wide range of working spans covers both small farmers with small tractors and large agricultural holdings equipped with powerful tractors.
During one run the soil is perfectly tilled to the state required for sowing of crops. The advantage of the machine is excellent levelling of the surface, fine crumbling of clods and formation of well-compacted seedbed. The land is perfectly levelled also due to levelling bars that can level and spread even high unevenness.
Seedbed combinators Kompaktomat are time-tested machines designed for seedbed preparation of the soil after ploughing.
Semi-mounted machines are offered with the working span from 3 m to 9.7 m. Wide range of working spans covers both small farmers with small tractors and large agricultural holdings equipped with powerful tractors.
During one run the soil is perfectly tilled to the state required for sowing of crops. The advantage of the machine is excellent levelling of the surface, fine crumbling of clods and formation of well-compacted seedbed. The land is perfectly levelled also due to levelling bars that can level and spread even high unevenness.
Due to high working speed, high working performance can be achieved even with lower working span of the Kompaktomat machine. A key consideration here is that due to its well-considered design and favourable weight Kompaktomat can prepare the soil after ploughing during one run, whereas the soil is tilled not only on the surface, but in the whole horizon.
During the run Kompaktomat performs several working operations, during which the surface of the soil is levelled and compacted to the depth. In the cultivated soil capillarity is restored and in the required depth the seedbed is formed. The clods are finely crumbled.
Optionally the combinator can be equipped with hydraulic adjustment of depth of the share section and hydraulic adjustment of the front leveller. Semi-mounted machines can also be equipped with the rear three-point linkage of category 2, where additional crumbling crosskill rollers can be aggregated. These rollers are suitable especially for summer when hard dry clods must be intensively crumbled. Aggregation of the seed drill and formation of productive sowing combination is another possibility. For this purpose Kompaktomat can also be equipped with additional water distribution.
The control elements of the seedbed combinator are designed in order to achieve maximum safety of workers. Simple but quality construction with minimum maintenance requirements.
High-strength refined materials in connection with eXtra STEEL line technology guarantee long service life of our machines even in the most difficult conditions.
Due to minimum of adjusting and lubricating points the operation and subsequent maintenance are very easy steps that anybody can perform.
The advantage of this machine is its multi-purspose and adjustability bringing high variability of work.
Differences between individual sections are described in more detail in the tab Accessory
Semi-mounted seedbed combinators Kompaktomat K 300 P – K 1000 PS enable aggregation with other devices or machines. For this purpose they must be additionally equipped with the rear three-point linkage of category 2; it is equipment over standard.
For aggregation with e.g. crumbling rollers it is sufficient to additionally equip the combinator with the rear three-point linkage only.
For aggregation with a pneumatic seed drill, the combinator can be extended by the hydraulic drive of fan and hydraulic circuit for control of the seed drill markers.
| Technical parameters | Units | Kompaktomat K 300 P |
Kompaktomat K 400 PS |
Kompaktomat K 450 PS |
Kompaktomat K 500 PS |
Kompaktomat K 600 PS |
|---|---|---|---|---|---|---|
| Working width | mm | 3 000 | 4 000 | 4 500 | 5 000 | 6 000 |
| Transport width | mm | 3 000 | 3 000 | 3 000 | 3 000 | 3 000 |
| Transport height | mm | 1 650 | 2 670 | 3 030 | 2 790 | 3 230 |
| Total machine length | mm | 5 965 | 5 965 | 5 965 | 6 105 | 6 105 |
| Working depth | mm | 0–100 | 0–100 | 0–100 | 0–100 | 0–100 |
| Number of tines – duck foot AL Number of tines – chisel CF Number of tines – duck foot AP |
pcs | 13 30 12 |
18 39 16 |
20 47 20 |
23 49 23 |
27 59 24 |
| Working performance | ha/h | 2,2–3,2 | 3–4 | 3,5–4,5 | 3–5 | 3,5–6 |
| Towing vehicle 1 | kW HP |
70 95 |
90 125 |
110 150 |
120 165 |
130 180 |
| Working speed | km/h | 10–14 | 10–14 | 10–14 | 10–14 | 10–14 |
| Maximum transport speed 4 | km/h | 30 | 30 | 30 | 30 | 30 |
| Maximum slope availability | ° | 11 | 6 | 6 | 6 | 6 |
| Dimension of tyre - transport | 400/60-15,5 | 400/60-15,5 | 400/60-15,5 | 19,0/45-17 | 19,0/45-17 | |
| Number of hydraulic circuits / pressure | bar | 2–4 / 200 | 2–4 / 200 | 2–4 / 200 | 2–4 / 200 | 2–4 / 200 |
| Number of quick-coupling devices / type | 4–8 / ISO 12,5 | 4–8 / ISO 12,5 | 4–8 / ISO 12,5 | 4–8 / ISO 12,5 | 4–8 / ISO 12,5 | |
|
Tractor hitch requirement |
mm | 1 010 (920) |
1 010 (920) |
1 010 (920) |
1 010 (920) |
1 010 (920) |
| Tractor hitch requirement Hole diameter of lower suspension joints for machine suspension pins (alternative Ø) |
mm | 37,5 (29) |
37,5 (29) |
37,5 (29) |
37,5 (29) |
37,5 (29) |
| Tractor hitch requirement | TPH cat. 2 and 3; lower hitch K80; eye Ø 40, 50, 70 mm | |||||
| Axle load | kg | 1 960 | 2 080 | 2 240 | 2 730 | 2 950 |
| Machine weight 2 | kg | 2 360 | 3 010 | 3 340 | 4 025 | 4 360 |
| Technical parameters | Units | Kompaktomat K 500 PS |
Kompaktomat K 600 PS |
Kompaktomat K 700 PS |
Kompaktomat K 800 PS |
Kompaktomat K 1000 PS |
|---|---|---|---|---|---|---|
| Working width | mm | 5 000 | 6 000 | 7 000 | 8 000 | 9 850 |
| Transport width | mm | 3 000 | 3 000 | 3 000 | 3 000 | 3 000 |
| Transport height | mm | 2 790 | 3 230 | 3 830 | 4 000 | 4 000 |
| Total machine length | mm | 6 105 | 6 105 | 6 105 | 6 105 | 6 660 |
| Working depth | mm | 0–100 | 0–100 | 0–100 | 0–100 | 0–100 |
| Number of tines – duck foot AL Number of tines – chisel CF Number of tines – duck foot AP |
pcs | 23 49 23 |
27 59 24 |
31 69 31 |
35 77 32 |
43 91 38 |
| Working performance | ha/h | 3–5 | 3,5–6 | 4,5–7 | 5,5–8 | 8,5–10 |
| Towing vehicle 1 | kW HP |
120 165 |
130 180 |
150 205 |
160 220 |
180 245 |
| Working speed | km/h | 10–14 | 10–14 | 10–14 | 10–14 | 10–14 |
| Maximum transport speed 4 | km/h | 30 | 30 | 30 | 30 | 30 |
| Maximum slope availability | ° | 6 | 6 | 6 | 6 | 6 |
| Dimension of tyre - transport | 19,0/45-17 | 19,0/45-17 | 19,0/45-17 | 19,0/45-17 | 19,0/45-17 | |
| Brake type / distribution 3 | air / two-line | air / two-line | air / two-line | air / two-line | air / two-line | |
| Required pressure 3 | kPa | 8,5 | 8,5 | 8,5 | 8,5 | 8,5 |
| Dimensions of brakes | 300/60 | 300/60 | 300/60 | 300/60 | 300/90 | |
| Number of hydraulic circuits / pressure | bar | 2–4 / 200 | 2–4 / 200 | 2–4 / 200 | 2–4 / 200 | 2–4 / 200 |
| Number of quick-coupling devices / type | 4–8 / ISO 12,5 | 4–8 / ISO 12,5 | 4–8 / ISO 12,5 | 4–8 / ISO 12,5 | 4–8 / ISO 12,5 | |
|
Tractor hitch requirement |
mm | 1 010 (920) |
1 010 (920) |
1 010 (1 045) |
1 010 (1 045) |
1 010 (1 045) |
| Tractor hitch requirement Hole diameter of lower suspension joints for machine suspension pins (alternative Ø) |
mm | 37,5 (29) |
37,5 (29) |
37,5 (50) |
37,5 (50) |
37,5 (50) |
| Tractor hitch requirement | TPH cat. 2 and 3; lower hitch K80; eye Ø 40, 50, 70 mm | |||||
| Axle load | kg | 2 730 | 2 950 | 3 360 | 3 620 | 4 520 |
| Machine weight 2 | kg | 4 025 | 4 360 | 4 960 | 5 345 | 6 920 |
| Technical parameters | Units | Kompaktomat K 500 PS LONG |
Kompaktomat K 600 PS LONG |
Kompaktomat K 700 PS LONG |
Kompaktomat K 800 PS LONG |
Kompaktomat K 1000 PS LONG |
|---|---|---|---|---|---|---|
| Working width | mm | 5 000 | 6 000 | 7 000 | 8 000 | 10 000 |
| Transport width | mm | 3 000 | 3 000 | 3 000 | 3 000 | 3 000 |
| Transport height | mm | 2 790 | 3 230 | 3 830 | 4 000 | 4 000 |
| Total machine length | mm | 6 355 | 6 355 | 6 355 | 6 355 | 6 910 |
| Working depth | mm | 0–100 | 0–100 | 0–100 | 0–100 | 0–100 |
| Number of tines – duck foot AL Number of tines – duck foot AL4 Number of tines – chisel CF Number of tines – duck foot AP |
pcs | 23 41 49 23 |
27 47 59 24 |
31 55 69 31 |
35 61 77 32 |
43 91 38 76 |
| Working performance | ha/h | 3–5 | 3,5–6 | 4,5–7 | 5,5–8 | 8,5–10,0 |
| Towing vehicle 1 | kW HP |
120 165 |
130 180 |
150 205 |
160 220 |
180 245 |
| Working speed | km/h | 10–14 | 10–14 | 10–14 | 10–14 | 10–14 |
| Maximum transport speed 4 | km/h | 30 | 30 | 30 | 30 | 30 |
| Maximum slope availability | ° | 6 | 6 | 6 | 6 | 6 |
| Dimension of tyre - transport | 19,0/45-17 | 19,0/45-17 | 19,0/45-17 | 19,0/45-17 | 19,0/45-17 | |
| Brake type / distribution 3 | air / two-line | air / two-line | air / two-line | air / two-line | air / two-line | |
| Required pressure 3 | kPa | 8,5 | 8,5 | 8,5 | 8,5 | 8,5 |
| Braked / unbraked variant | yes / yes | yes / yes | yes / yes | yes / no | yes / no | |
| Dimensions of brakes | 300/60 | 300/60 | 300/60 | 300/60 | 300/60 | |
| Number of hydraulic circuits / pressure | bar | 2–4 / 200 | 2–4 / 200 | 2–4 / 200 | 2–4 / 200 | 2–4 / 200 |
| Number of quick-coupling devices / type | 4–8 / ISO 12,5 | 4–8 / ISO 12,5 | 4–8 / ISO 12,5 | 4–8 / ISO 12,5 | 4–8 / ISO 12,5 | |
|
Tractor hitch requirement |
mm | 1 010 (920) |
1 010 (920) |
1 010 (1 045) |
1 010 (1 045) |
1 010 (1 045) |
| Tractor hitch requirement Hole diameter of lower suspension joints for machine suspension pins (alternative Ø) |
mm | 37,5 (29) |
37,5 (29) |
37,5 (50) |
37,5 (50) |
37,5 (50) |
| Tractor hitch requirement | TPH cat. 2 and 3; lower hitch K80; eye Ø 40, 50, 70 mm | |||||
| Axle load | kg | 2 810 | 3 030 | 3 460 | 3 720 | 4 850 |
| Machine weight 2 | kg | 4 125 | 4 460 | 5 110 | 5 495 | 7 420 |
1 Recommended towing vehicle, the actual pulling force may significantly change according to the tilling depth, soil conditions, inclination of land, wear of working units and their adjustment.
2 Machine variant weight: front bar roller, section AL, rear crosskill roller with leveller.
3 Alternative of the brake type: hydraulic, pressure 130 ± 5 bar (designed for the French market).
4 Transport / brake system: Follow national provisions valid for transport of machines on public roads. Verify legal provisions valid in the country, regulations on maximum allowable total weights and axle loads and also on necessary possible use of the brake system. If you have any questions, please contact our sales representative.
P - semi-mounted machine
PS - semi-mounted foldable machine
| Diameter | 400 mm |
| Weight | 170 kg/m |
May be applied as the rear roller only.
Excellent work in light, medium and heavy soils, quality compaction and clod crumbling.
| Diameter | 400 mm |
| Weight | 202 kg/m |
May be applied as the rear roller only.
Excellent work in light, medium and heavy soils, quality compaction and clod crumbling. When compared to crosskill roller, more intense clod crumbling.
| Diameter | 400 mm |
| Weight | 60 kg/m |
May be applied as the front and rear roller.
Quality clod crumbling. Suitable for wet conditions.
| Diameter | 400 mm |
| Weight | 60 kg/m |
May be applied as the front and rear roller.
Quality clod crumbling. Not very suitable for wet conditions.
| Diameter | 400 mm |
| Weight | 115 kg/m |
May be applied as the front and rear roller.
Quality work in all types of soil, good depth guiding, suitable even for more humid soils.
Proper selection of the type of the roller contributing significantly to the final quality of the tillage is very important. The selection of the type of the roller depends on the soil type and on the manner of use of the machine.
| Rollers | Crosskill CR |
Double crosskill DCR |
Bar BR |
Spiral bar SB |
Ring RR |
|---|---|---|---|---|---|
| Crumbling | ●●●● | ●●●● | ●●●○ | ●●●○ | ●●○○ |
| Stamping | ●●●● | ●●●● | ●●●○ | ●●●○ | ●●●● |
| Depth guiding | ●○○○ | ●●○○ | ●●●○ | ●●●○ | ●●●● |
| Resistance against clogging | ●●●○ | ●●●● | ●●○○ | ●●●○ | ●●●● |
| Suitability for stony soils | ●●○○ | ●●○○ | ●●●○ | ●●●○ | ●●●○ |
| Suitability for wet soils | ●●○○ | ●●●○ | ●○○○ | ●●●○ | ●●●● |
| Heavy soils | ●●●○ | ●●●● | ●●○○ | ●●○○ | ●●●○ |
| Medium soils | ●●●● | ●●●● | ●●●○ | ●●●○ | ●●●○ |
| Light soils | ●●●● | ●●●● | ●●●● | ●●●● | ●●●○ |
For the AL / AP section.
For the CF section.
For the CF section.
For the AL4 section.
The share section is equipped with duck foot shares of the width 25 cm in two rows. Each of the shares is protected with leaf spring. This share section is suitable for lighter soil conditions without crop residues. By default, the height-adjustable coordination bar is located behind the shares.
The share section is equipped with narrow shares of the width 3.5 cm in four rows. This share section is suitable for soil tillage in spring when it is not desirable to extract wet soil to the surface, or in heavy soils. Behind the shares, the directing bar is placed as standard.
The universal share section is equipped with duck foot shares of the width 25 cm in two rows. The shares are mounted on tine holders with geometry improving the throughflow of crop residues. Therefore, this share section is suitable for land with a higher amount of crushed crop residues and heavy soils. By default, the height-adjustable coordination bar is located behind the shares.
Variant for Kompaktomat LONG
Four-row section with shares mounted on flexible tines.
| Section | AL | AL-L 1 | CF | CF-L 1 | AP | AP-L 1 | AL4 1 |
|---|---|---|---|---|---|---|---|
|
Number of rows of shares (pcs) / |
2 / 400 | 2 / 510 | 4 / 240 | 4 / 265 | 2 / 490 | 2 / 600 | 4 / 270 |
| Leveller behind shares | ●●●● | ●●●● | ●●●● | ●●●● | ●●●● | ●●●● | ●●●● |
| Full-area tillage | ●●●● | ●●●● | ●●○○ | ●●○○ | ●●●● | ●●●● | ●●●● |
| Suitability for light soils | ●●●● | ●●●● | ●●●● | ●●●● | ●●●● | ●●●● | ●●●● |
| Suitability for medium soils | ●●●○ | ●●●○ | ●●●○ | ●●●○ | ●●●● | ●●●● | ●●●● |
| Suitability for heavy soils | ●●●○ | ●●●○ | ●●●○ | ●●●○ | ●●●● | ●●●● | ●●●● |
| Suitability for stony soils | ●●●○ | ●●●○ | ●●●○ | ●●●○ | ●●●● | ●●●● | ●●●○ |
| Suitability for wet soils | ●●○○ | ●●○○ | ●●●● | ●●●● | ●●○○ | ●●○○ | ●●●○ |
| Resistance against clogging | ●●○○ | ●●○○ | ●●●○ | ●●●○ | ●●●○ | ●●●○ | ●●●○ |
1 The section is designed for Kompaktomat LONG. It provides better throughput due to the extended spacing.
Automatically unprotected tractor track cultivator with the duck foor share. More suitable for lighter soils without the risk of “dragging” of wet clods to the surface.
Automatically unprotected tractor track cultivator with the chisel share. More suitable for heavier soils with the risk of “dragging” of wet clods to the surface.
Automatically unprotected leveller in the toothed profile. Massive construction for precise smoothing of the rough furrow.
FL = fixed mechanical skid, FH = fixed hydraulic skid.
Automatically unprotected leveller from separate flexible segments. Better clod crumbling.
L = Flexi-board, FB = hydraulic Flexi-board.
Passive levelling of the soil surface behind the rear roller. It can be applied behind all types of rear rollers.
Swing stops for possibility of more aggressive adjustment of the rear leveller.
Active crumbling of remaining clods behind the rear roller.
Active crumbling of remaining clods behind the rear roller.
Can be used for all types of rollers in Kompaktomat LONG.
Cannot be used after the rear double-row rollers in Kompaktomat PS.
Possibility of additionally mounting a single-hose or two-hose circuit for controlling the sowing machine markers to the Kompaktomat machine with the rear TPS.
Circuit for drive of pneumatic sowing machine fan can be optionally mounted on Kompaktomat with rear TPH.
In the rear part of the semi-mounted Kompaktomat machines, the rear hitch for aggregation with other machine can be installed. Part of the rear suspension is a two-hose circuit for folding the additional equipment.
T2, T3, T4 – aggregation into arms of the rear hitch.
T2 – drawing pins Ø 28 mm
T3 – drawing pins Ø 36 mm
T4 – drawing pins Ø 50 mm
C40, C50, C70 – aggregation into the solid agro-linkage. Maximum vertical load of the towing eye 3,000 kg.
C40 – drawing pin Ø 40 mm
C50 – drawing pin Ø 50 mm
C70 – drawing pin Ø 70 mm
K80 – aggregation into the solid agro-linkage. Maximum vertical load of the towing eye 3,000 kg.
K80 – towing ball 80 mm
Increased productivity:
Can also be installed additionally to older machines.
Increased productivity:
Can also be installed additionally to older machines.
Designed for Kompaktomat LONG.
Automatically released leveller with the option to set the bottom position. The leveller provides more intense mixing = finer soil structure.
